The electric pool robot cleaner HJ 2028 cleans the floor,walls and waterline of your pool.Through its broad pin type brush,it effectively rub the entire surface of pool.Its pump which is at a rate of15m³/h sucks all debris at the bottom to store them in a fine filter bag in big capacity.With a nice and innovative design,it will be the perfect parter for cleaning your pool.Designed to operate in all shapes of pool:retangular,oval,round,libreset forms with all coatings:tiles,flat bottom,gently sloping,diamond tips.Easy to move out from the water with an extra caddy.
Supplied with 18 meters of cable and a powerful pump with a suction capacity of 15m³/h,it cleans pools up to 12m on a cycle of 3 hours or 5 hours with a speed of 12m/mn.Filter as fine as 100 microns,effective in every coner,the robot HJ2028 cleans and brushes the floor,walls and waterline of your pool effectively.Independent and reliable,by using it,the cleanup will soon be forgotten and you will have time to do something else during its working.The operation system is simple as “plug&play”,you plug it in,put it on and it does the rest.
Rated output power: 150W Frequency of remote control: 2.4G
Cable length: 18m
Cleaning band width: 358mm Maximum cleaning area: 200m²
Filtering capacity: 15m³/h
Filtering capability: 400µm (400µm filter bags are suggested to be
used at the beginning of the season),
Optional: 10µm/100µm /200µm
Water temperature of use: 10°C - 32°C Creeping speed: 12m/min
IP Grade: cleaner-IP68; power supply unit-IPX4 Working temperature: 10°C - 40°C
Weight of cleaner: 9.5kg (without cable)
Warranty 2 years for motors and electrical parts.
All spare parts avaliable on request.
After sales service in China and Europe.
With the concept of "initiativity and sustained innovation", we'll meet the market requirements by constantly providing efficient and powerful new models.
The HJ2028 Automatic Swimming Pool Cleaner consists of power supply unit, cleaner body, caddy (Optional) and remote control. The following are the components cleaner(see Fig.4-1/4-2/4-3/4-4).
Operation of control remote(RC if you have):
Operation of RC A:
1) Power on: Press "ON" (Fig.7-1-8), cleaner switch into standby mode.
2) Power off: The cleaner will stop working after pressing "OFF" at any mode.
3) FWD by manu mode: Firstly, switch into standby mode by following step (1), then press FWD (Fig.7-1-7) and the cleaner will move forward.
4) REW by manu mode: Firstly, switch into standby mode by following step (1), then press REW (Fig.7-1-4) and the cleaner will move reward.
5) 3h AUTO mode: Firstly, switch into standby mode by following step (1), then press AUTO/3h (Fig.7-1-6) and the cleaner will work in 3h AUTO mode.
6) 5h AUTO mode: Firstly, switch into standby mode by following step (1), then press AUTO/5H (Fig.7-1-3) and the cleaner will work in/ switch into 5h AUTO working mode.
Operation of RC B:
1)Automatic working: Press AUTO 1H,AUTO 2H, AUTO 3H or AUTO 4H into automatic working for 1h, 2h, 3h or 4h;
2)Manual forward: Press “AVT” (Fig.7-2-7) to move forward;
3)Manual backward: Press “ARR” (Fig.7-2-4) to move backward;
4)Power off: Press “ARRET” to stop the cleaner in any mode.
Works after use cleaner:
Removing Cleaner from Pool
The cleaner will power off automatically after one cleaning cycle. Unplug the power cable, pull the cable line slightly and lift the cleaner by carrying the stationary ring on the lock nut .
1) In order not to scratch the pool wall or damage the cleaner, avoid the cleaner touching the pool wall during carrying out from pool.
2) Before carrying outside from pool, suspend the cleaner above water for about 10-15 seconds to release the water remaining inside the cleaner.
3) To carry out the cleaner from pool, please hold the top handle only,never pull cable .
4)Put the cleaner on the edge of pool, open the lock nut, and remove the top cover. Then take out the filter cartridge and take off the filter bags.
Founction&instructions for sliding block
1)The Sliding Block is located at the bottom of the cleaner, beneath the motor assembly. 2)Please adjust cleaner weight by taking off the weight block. The default weight block position is carefully tested by manufacturer which is not suggested to change unless the cleaner is too weight in water (filt -er bag is clean), or could even take off the weight block cover too.
This Sliding Block can also be used to adjust the cleaner to fit for different pool conditions (ex. Pure water and salt water). Please contact local dealer if the cleaner floats above pool floor.
As a manufacturer of Sino-French joint-venture, we're established in 2005, key product includes swimming pool cleaner and related accessories. We have strong technical ability, good financial condition and a professional team of both Chinese and French engineers, as well as experienced technical workers and a elite management team led by general manager who has many years experience in France. We committed to research, production, selling and after sales service, the R&D centre and European marketing centre is located in France and is in charge of new product developing, design and communications with European super markets and professional shops, there is a perfect after sales service system in Europe with manufacturing base in TEDA of Tianjin, the plan of opening new branches in the USA, Australia and Middle east is also in process.
We attend professional shows held world wide every year and our market covers 27 countries in Europe, Middle east, North-Africa, Australia and South-east Asia, we have good selling records in more than 10 chains super markets like Carrefour and Auchan in France and Spain and gained good reputation with our stable quality and competitive price.